We welcome you into the family of Electropedic Stair Lifts. Since 1964, we are the manufacturer of the Electropedic Bed. In 1985, we expanded into a full line of Electric Medical Equipment.
Before you buy an Electric Stair Lift, compare Price, Quality, Guarantee and Service. To give you a price and recommendation, we first need to know if your stair lift is basically straight up and down (and approximately how many feet or steps) - or is it a custom right angle or curved unit (although many people buy (2) two straight units to save on the price of a custom unit.)
New Straight Units have a Suggested Retail price usually between $2895.00 and (outdoor units) $5495.00. Used Stair Lifts are always 1/2 OFF! Custom Curved Units usually run between $12,500 and $15,000.
Most people buy a straight, inside the home unit. Some people need an outdoor unit. Some people need a unit that goes into a commerical setting (although Acorn has a standard key switch.)
We need your confirmation that your stair case is made out of wood; and also a confirmation that your bottom floor or landing is either wood, concrete or marble. (It is always recommended that the unit be installed resting on the landing; although, it is not always "wanted" or practical. Some models have a flip up bottom track that is not attached to the floor - and can also get out of the way of any passage way or door.)
The unit is ideally installed about 6 to 8" pass the lip of the top stair so you can exit the unit is a comfortable sitting position.
We explain to you that the track for the units are not installed onto the wall, but rest on the steps. The rail is installed onto the stairway with about 8 brackets.
We find out if you are planning to put the unit on the left side or the right side (we always ask if you are downstairs, looking up . . . what side are you planning to install your stairway lift.) Then we may ask you to confirm if there are any side rails or doors or access ways that may get in the way.
We are also going to need an outlet somewhere close to the stairway unit.
We explain how most units are actually powered by their batteries. You are actually plugging in a battery charger. This system means that your stair lift will also work during a power outage.
Then we may ask about your height and weight. Most units have a 275 Pound weight capability; but there are specific units with a 350, 400 and 500 pound weight capability.
We ask your height to make sure the unit will fit your height properly. Most units have a footrest height adjustment (good for people who are short); but some units also have a seat height adjustment; which is beneficial to those 6 feet and taller.
Then we ask your health conditions. Units are designed so they can be used without anyone else's assistance. All units come with a seat belt; and the units are made to go upstairs and downstairs at the simple touch of a button. The button control is usually put on the right side, so we need to know if both hands are working the same. The new unit by Acorn has the controls coming standard on both sides. We need to know if you are going to be operating the unit yourself, or with someone. All units come standard with both top and bottom remote controls; so someone else can be actually pushing the bottons.
Some people cannot bend their legs into a sitting position; and there are units that allow you to perch or stand.
We need to know if once you are at the top or bottom of the stairway, if you are going to be transfering to a walker or a wheelchair. All units have a swivel seat for the stop, some units swivel both top and bottom; all units have flip up arm rests except the SRE-1550 which have special swing-away (horizontal) arm rests.
Are you going to install yourself or do you need our assistance? We have a factory trained Stair Lift Installer on our staff to assist in your installation. If you are planning to put it in yourself, most people buy the 16 foot or 20 foot rails and do the final cutting themselves. The Summit Stair Lift Manufacturer will cut the rail to the exact size you need (we need you to take an actual measurement from the very top lip of the stairway to the landing).
By now we have a good idea of what price to quote you. We guarantee the World's Lowest Price and will always offer you an exact written or Email quotation and brochure and online video! Our company will also let you know if we have any National Advertised Stair Lift Specials. (We currently advertise in AARP Modern Maturity, VFW, American Legion, Retired Officer, Good Old Days, . . .)
We will also gladly go over the standard features - and options - of the unit we are recommending. Standard features of new units usually include a beige color, vinyl or fabric seat, low-profile design (14" - the exact specification of the unit with the seat and foot rests folded up), aluminum track, the safety features built in (automatically stopping when the footrest or arm rest hits something), the battery charging system, electronic brakes, battery powered smooth start operation, wireless remote controls, built-in diagnostics (most units today have built in diagnostics letting you know if anything needs servicing on the unit), . . . .
We ask you a lot of questions, and we share with you our experience. We want you to know, today, all the manufacturer's of electric stair lifts are very good. But getting the right unit for your home and needs - at the right price - is our goal. Please call (800)727-1954 and talk to an Electropedic Stair Lift Specialist. You'll be glad you did.
BRUNO INDEPENDENT LIVING AIDS
Bruno Independent Living Aids, founded in 1984, is family owned and operated, and has a proud history of innovation that provides solutions for individuals who may face challenges with mobility. Our products: Bruno stair lifts, vehicle lifts and Turning Automotive SeatingTM (TAS) open up new vistas of independence for many. Our stairlifts help overcome the barriers that stairs in your home can create. A Bruno stairlift in your home allows you to stay in your home and enjoy it to the fullest! With electric scoote wheelchair lifts and Turning Automotive Seating in our product lineup, we're able to equip almost any vehicle: automobiles, vans, pickups, minivans and SUVs.
Bruno Independent Living Aids
WORLD'S LOWEST PRICES
1(800)-446-5040
Bruno living aids Scooter, Lifts, Scooter-Lift, Stair-Lift
Welcome to Bruno Stairlifts! As North America's leading manufacturer of stairlifts, Bruno offers a complete line of battery-powered stairlifts for residential and commercial use. With a Bruno stairlift, you can enjoy all of your home-our stairlifts are designed to take you up and down stairs, safely and effortlessly, any time you desire!
We offer both indoor straight- and custom-curved rail models as well as our Industry-Exclusive Model SRE-2000 Electra-Ride Elite stairlift for indoor or outdoor use, designed with a 400 lb. weight capacity.
Commitment to Excellence
Founded over 20 years ago, Bruno Independent Living Aids, Inc., is proud to be an ISO-9001 Certified manufacturer. In pursuit of this goal, Bruno is proud to be the only manufacturer of stairlifts, vehicle lifts, scooters, power chairs and Turning Automotive Seating(TAS) products in the U.S. to become ISO-9001 Certified. This is one of the most stringent and widely recognized quality standards in the world. It is your assurance that Bruno is committed to providing you with the finest products of their kind in the Industry. As the Industry leader, we stand behind our reputation for providing superior quality. In addition, our on-going commitment to developing the highest quality assistive technology has resulted in numerous business awards.

THE ELECTRA RIDE LT
Model SRE-2700
Model SRE-1550

ELECTRA-RIDE III
Model CRE-2100
Model SRE-2000
Compact installation - rail is only 5 inches off the wall!
Adjustable footrest for added comfort.
Battery operation insures safe operation - even during power outages!
Comfortable seat width is adjustable from 19 to 24 1/2"
Exclusive Industry-First 400 lb. weight capacity!
OUTDOOR ELECTRA-RIDE ELITE
Model SRE-2000E
Design specifically for outdoor use with the same quality, comfort and convenience of Bruno indoor stairlifts
Weather-resistant cover system travels with chair - protects rider from the elements and protects stairlift when not in use.
Tested to operate in temperatures ranging from 25°F to 125°F. The electrical enclosure provides protection against spraying water.
Durable, powder-coated paint finish provides additional weather protection.
Exclusive Industry-First 400 lb. weight capacity!

CUSTOM RAIL STAIRLIFTS
Who will install my Bruno stairlift?
All Bruno stairlifts are sold, installed, and serviced by our world wide network of dealers. Bruno stairlift dealers are factory trained to evaluate your specific mobility needs and help you choose the best stairlift solution along with providing professional installation and service.
What is the length of the warranty on a Bruno stair lift?
Bruno stairlifts come with our Gold Warranty which features 2 years on all parts and 5 years on major components that include the main drive system (i.e. gear box, motor, and rail system). The warranty is valid on all Bruno stairlift units that have been installed by Bruno factory-trained dealers, providing you with years of worry-free access up and down your staircase.
What type of modification will be needed on my staircase for the unit to fit?
In most cases there will be no modification needed. That's because Bruno stairlift models are designed to fit your existing staircase using our clamping systems which mount directly to the treads of your steps. No structural modification to your wall or staircase is required.
How narrow can my staircase be?
Depending on which Bruno stairlift model you choose, the unit - in its operating position - will take up about 24"-26". The user's knees when seated in the Bruno stairlift, are generally what take up the most room. This is why we recommend a 32" wide staircase. (Please keep in mind that some local building codes require a wider staircase.) Fitting a stairlift on tighter a staircase is possible and should be reviewed with your local Bruno dealer.
How quickly can I get a Bruno stairlift?
Many of our local Bruno dealers have units in stock for straight-rail applications. Bruno also stocks units for most straight rail applications for quick shipment from our Wisconsin headquarters. Please contact your local Bruno dealer to evaluate your staircase for curved-rail applications and to determine a lead time.
How long does it take to install a Bruno stairlift?
A Bruno factory-trained stairlift dealer can typically install most units in less than half a day with many installations taking just an hour or two. The installer will make sure that you are completely trained on the operation of the unit and be in and out of our home with little interruption to your day.
Can a Bruno stairlift be installed in my church or lodge?
Yes, but the requirements for these types of buildings are different than residential installations. Please contact the local Bruno stairlift dealer to review all the requirements for installation.
What happens if I lose power in my house?
All Bruno stairlifts are battery powered and will continue to operate even if power is lost in your home. The unit will typically run for 3-4 days or 15-20 trips without being recharged. When your power comes back on, the batteries will recharge automatically.
How long will the batteries last?
Batteries used on Bruno stairlifts will typically last 3-5 years depending on the use and application of the unit. Replacement batteries can be purchased from your Bruno dealer.
I have a staircase that turns; will a Bruno stairlift fit?
Yes, Bruno's model Electra-RideTM III is designed to be custom fitted for any staircase configuration and can be installed on either side of most staircases to best fit your house.
Where are Bruno stairlifts made?
Bruno is the NUMBER ONE provider of stairlifts in both the USA and in Canada and they are made right here in the USA. All Bruno stairlift are designed and assembled at our headquarters in Oconomowoc, WI.
MOBILITY PROGRAMS
REQUEST
INFORMATION FORM
Pricing
Policy:
Bruno Independent Living Aids, Inc. distributes its products through independent
dealers. Each dealer is trained to evaluate, install and service
Bruno products which may affect the installed price. For a pricing
inquiry, please submit your request using our request form and we will send
you product literature and the name of your nearest Bruno dealer.

OUT-SIDER III®
Lets you carry your scooter fully assembled and keeps your trunk space available for other things.
The Out-Sider III® is simple to operate. Just turn the key and move the control lever to the position marked ARROW UP or ARROW DOWN. The unit automatically lifts and lowers the scooter, as well as raising and lowering the hold-tite lock-down mechanism.
The Out-Sider III can raise and store 3 or 4 wheel scooters weighing up to 300 lbs., using a Class III hitch with a 2" receiver. The Out-Sider III system is fully automatic and is superior to any other rear exterior lift. The unit is powder coated and assembled with stainless steel fasteners for long life. In addition to these features, a special weight sensing device applies exactly the right amount of pressure to the hold-tite device to secure the scooter.
Bruno's Out-Sider III features an ON-OFF key for greater security, and an automatic emergency safety latch prevents the platform from lowering. As a result, the Out-Sider III gives you an easy to use, secure way to transport your scooter.
The Out-Sider III is powered by your vehicle's battery and is delivered fully equipped, including a lighted license plate holder, reflectors and a D.O.T. approved center brake light for added safety.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.
OUT-SIDER MERIDIAN
The NEW Model ASL-250 Out-Sider Meridian is the ideal solution for the transportation of your electric scooter or power chair! With such great features as a low-profile compact design, lightweight, robust construction, durable, length-adjustable, drive on/off aluminum platform and stainless steel hardware, you can count on the Out-Sider Meridian to deliver miles of carefree service! Trust Bruno for quality and durability!
The Out-Sider Meridian Lift is designed for maximum safety. Because of our rigorous internal and external independent lab testing, we know the NEW, lightweight Out-Sider Meridian Lift can safely handle and transport our recommended weight capacity for sedans, minivans, SUVs, medium-size crossover vehicles, compact/midsize pickup trucks and full-size vans. Trust Bruno for safety and reliability!
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.
OUTSIDER MICRO
The new Bruno Out-Sider is a "low-cost and light-weight" exterior vehicle lift designed to handle today's popular travel scooters. The Out-Sider Micro easily installs on vehicles with a 1-1/4" hitch receiver and provides a 125 lb./57 kg. lifting capacity making it ideal for applications with compact vehicles.
The Out-Sider Micro offers ease of use and a clear rear view thanks to the low profile design. The Out-Sider Micro offers fewer moving parts than any other outside vehicle lift and is road and laboratory tested by a certified testing facility.
OFFSET FOLDAWAY
Bruno's Offset Fold-Away eliminates the struggle of taking apart your trunk lift. The effort to lift the mast is a mere two pounds. It uses dual-spring assist and color-keyed hand-holds to make it so easy, almost anyone can do it!.
The offset design feature, in combination with Bruno's industry-leading adjustable low-profile outer arm, gives you the flexibility to load a partially-assembled scooter from the driver side, behind the vehicle or from the curb side.
Bruno's new Offset Fold-Away lift is engineered to operate with an ergonomic pendant built into the outer lift arm.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

SPACE-SAVER®
Exceptional versatility with Bruno's take-apart lift, to help you store your scooter in vehicles with smaller trunks.
The Space-Saver is a take-apart lift that solves the problem of storing a scooter in smaller vehicles with limited trunk space.
The Space-Saver fits closer to the interior trunk wall providing a tighter arc when manually swinging the scooter in and out of the trunk. This allows scooters to be stored in spaces that won't work with more conventional lift designs, and the rotation of the lift arm makes it possible to raise and lower the scooter at the rear or side of the vehicle.
The Space-Saver can be stored anywhere, in the trunk or inside the vehicle itself. And when an additional tower base installation kit is ordered, the lift can be used in more than one vehicle. Contact Bruno's Technical Application Department
The Space-Saver is fully adjustable for height and length and can raise scooters weighing up to 180 lbs. (82 kgs). The lift's tower base can be easily adjusted to fit nearly any car's trunk, ensuring a useful, reliable installation.
The Space-Saver is lightweight and assembly and disassembly can be completed in three simple steps, quickly and easily.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

OFFSET SPACE-SAVER®
Now you can load your scooter in the trunk of your compact sedan with this unique offset lift from Bruno.
The Offset Space-Saver from Bruno gives you the flexibility to load a partially assembled scooter in the trunk of today's smaller cars. The unique offset design of the lift arm allows you to position your scooter inside narrow trunk openings.
The Offset Space-Saver permits lift installations for vehicles with trunks that previously were considered too small. This means that you don't have to purchase a different type of car. And it means you don't have to go without the benefit of a lift any longer.
The Offset Space-Saver is designed with a low-profile outer arm lift assique offset design of the lift arm allows you to position your scooter inside narrow trunk openings.
The Offset Space-Saver permits lift installations for vehicles with trunks that previously were considered too small. This means that you don't have to purchase a different type of car. And it means you don't have to go without the benefit of a lift any longer.
The Offset Space-Saver is designed with a low-profile outer arm lift assembly to make storing your scooter even easier. All controls are located conveniently on top of the lift arm. Just press a button and the Offset Space-Saver eliminates the struggle of raising and lowering your scooter.
The Offset Spacer-Saver can be stored anywhere, in the trunk or inside the vehicle. It disassembles quickly and easily, requiring only three steps. When an additional tower base assembly is ordered, it can even be used in more than one vehicle. Contact Bruno's Technical Application Department for installation details.
The Offset Space-Saver can raise and store many types of three-wheel scooters weighing up to 180 lbs, with either front or rear drive.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.
SCOOTER-LIFT JR.®
Now you can lift and store your scooter in the trunk of your auto the easy way. It can also be adapted for some station wagons and hatchbacks.
The Scooter-Lift Jr. lift is electrically powered from the vehicle's battery. Simply press a button on the controller and the Scooter-Lift Jr. raises and lowers your scooter, effortlessly.
Bruno's Scooter-Lift Jr. can be adapted to operate in station wagons and hatchbacks. This versatility can provide a significant benefit when a new vehicle purchase is not in your budget.
Bruno's Scooter-Lift Jr. can end the struggle of manually trying to lift and store a scooter in the trunk or hatch opening of your vehicle. The Scooter-Lift Jr. gives you the convenience you need to transport your scooter, and the freedom to travel when and where you want to.
The Scooter-Lift Jr. was designed to help raise and store three-wheeled scooters in most auto trunks, station wagons or hatchbacks, as long as the opening is large enough to accept the partially disassembled scooter and compact lift.
The Scooter-Lift Jr. is also available with the added option of a spring-assist feature. This further reduces the effort needed to raise and lower the lift arm before and after use.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

SCOOTER-LIFT SR.®
Now you can lift and store your fully assembled scooter in the rear of your van or minivan the easy way.
The Scooter-Lift Sr. is electrically powered from the vehicle's battery. Simply press a button on the controller and the Scooter-Lift Sr. raises and lowers your scooter, allowing you to manually swing it in or out of the vehicle.
The Scooter-Lift Sr. is also available as the VSL-560, featuring Bruno's exclusive Patented Adjustable Sub-Base. The Adjustable Sub-Base fits most vans, adds stability, is compact and allows for faster, simpler installation.
Bruno's Scooter-Lift Sr. can end the struggle of manually trying to lift and store a scooter in your van or minivan. The Scooter-Lift Sr. gives you the convenience you need to transport your scooter and the freedom to travel when and where you like.
The Bruno Scooter-Lift Sr. makes taking your scooter with you simple and easy. No need to remove and store the seat, and our custom manufactured C-Arm and T-Bar Docking Device allow you to raise you scooter at the touch of a button.
The Scooter-Lift Sr. is also available with the added option of a spring-assist feature. this reduces the effort needed to raise and lower the lift arm before and after use.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

BIG-LIFTER™
Now you can lift your scooter weighing up to 400 pounds and place them in the rear of most vans, minivans and sport utility vehicles.
The Bruno Big-Lifter is electrically powered from the vehicle's battery.
Simply press a button on the controller and the Big-Lifter raises and lowers your fully assembled power chair weighing up to 300 pounds, allowing you to manually swing it in or out of the vehicle. Minimum strength is required.
The Bruno Big-Lifter manual swing has a low-resistance design that is easy to swing in and out, and comes complete with a lifting device designed specifically for the power chair.
The Bruno Big-Lifter is a fully adjustable lift that can be installed in just a few hours and requires no structural modification to the vehicle.
The Bruno Big-Lifter securely stores your scooter or power chair in the rear of most vans, minivans and sport utility vehicles: positioned behind the rear seat.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

CURB-SIDER®
Now you can lift and store your fully assembled scooter in the rear of your van or minivan the easy way.
Bruno's New Curb-Sider can end the struggle of trying to manually lift and store a scooter in your van or minivan. The New Bruno Curb-Sider was designed to fit most types of vans, minivans, sport utility vehicles and pickups with caps. Plus, the New Curb-Sider can be adapted for use with some types of power wheelchairs, increasing its versatility.
The New Curb-Sider lift is electrically powered from the vehicle's battery. Simply press a button on the hand-held controller, and the New Curb-Sider raises and lowers any scooter weighing up to 200 lbs., effortlessly.
Bruno's New Curb-Sider provides a unique 180 degree powered rotation, which makes it possible to raise, lower and rotate a fully assembled scooter on the curb, at the side of your vehicle, or directly behind it. The New Curb-Sider's rotation feature allows it to stow scooters in vehicles with tailgates.
The lift arm can be folded vertically when not in use and installation does not require any structural modifications to your vehicle.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

SCOOTER-LIFT II
Lift and store your fully assembled scooter or wheelchair through either side sliding door of minivans.
The Scooter-Lift II can raise and store a fully assembled scooter or wheelchair through the driver's or passenger's side sliding door of minivans, and passenger side doors of full size vans.
The Scooter-Lift II requires very little arm strength, balance or effort to use. It is so compact that even in a minivan, there is still enough room for three passengers to sit comfortably in the rear seat. With scooter removed, or when traveling without the scooter, entry and exit is easy since the door opening remains unobstructed.
Bruno's Scooter-Lift II also features an optional installation assembly that eliminates drilling any holes in the floor of the vehicle. This means easier removal when it comes time to transfer the lift in and out of a minivan. Contact Bruno's Technical Applications Department about specific applications for this system.
The Scooter-Lift II can be used for either three-or four-wheel scooters and manual folding or power wheelchairs weighing up to 200 lbs. (91k). The Scooter-Lift II's hand-held controller makes this lift simple and easy to use. The Scooter-Lift II uses electrical power from the vehicle's battery and all lift operations are automatic. You only need to help guide the scooter or wheelchair into place.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers

CURB-SIDER SUPER XL®
Now you can lift and store your fully assembled scooter in the rear of your van or minivan the easy way.
Bruno's New Curb-Sider can end the struggle of trying to manually lift and store a scooter in your van or minivan. The New Bruno Curb-Sider was designed to fit most types of vans, minivans, sport utility vehicles and pickups with caps. Plus, the New Curb-Sider can be adapted for use with some types of power wheelchairs, increasing its versatility.
The New Curb-Sider lift is electrically powered from the vehicle's battery. Simply press a button on the hand-held controller, and the New Curb-Sider raises and lowers any scooter weighing up to 200 lbs., effortlessly.
Bruno's New Curb-Sider provides a unique 180 degree powered rotation, which makes it possible to raise, lower and rotate a fully assembled scooter on the curb, at the side of your vehicle, or directly behind it. The New Curb-Sider's rotation feature allows it to stow scooters in vehicles with tailgates.
The lift arm can be folded vertically when not in use and installation does not require any structural modifications to your vehicle.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.
CURBSIDER XL3
Outer Arm provides for a 6" powered telescoping extension. Combined with 6" of positioning allows for a 12" total adjustment.
The BRUNO VSL-690 CURB-SIDER SUPER XL3 is a lift for the rear of minivans, full-size vans, sport utility vehicles and station wagons.
The BRUNO VSL-690 CURB-SIDER SUPER XL3 3-axis control unit allows wider and larger scooters, power wheelchairs and equipment to fit into smaller vehicle openings like the new 2001 Daimler Chrysler minivan (with a power hatch).
This unique new lift is easy to operate with an ergonomic control pendent and can lift up to 400 lbs. A 200 lb. lifting capacity version for smaller vehicles such as the Daimler Chrysler PT Cruiser is available.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.

CAB-SIDER
BRUNO MODEL PUL-1700
Now you can enjoy owing a pickup truck along with the advantage of storing your folding wheelchair inside, out of the weather.
The Cab-Sider gives you the advantage of driving a pickup while being able to store your chair inside, out of the weather. The truck bed is free to use for other things and can even be equipped with a cap, if desired.
Bruno's Cab-Sider is compact enough to allow small items or soft luggage to be placed in the cab area when the chair is stored. Simple installation means easy removal when it comes time to trade in your vehicle.
The Cab-Sider is simple to operate. This easy to use wheelchair lift is electrically powered. All you need to do is roll the chair next to the vehicle, transfer and then use the hand-held controller to do the rest. Unloading the chair is just as simple and trouble-free.
Bruno also offers the EZ RIZER seat lift system to assist wheelchair users that may find it difficult to transfer into and out of full-size trucks. Call Bruno's Technical Applications Department for additional information.
The Cab-Sider is available for any full size or compact truck that features an extended cab with a fourth door. This includes Dodge Ram, Chevy S-10, Chevy C/K, Siverado, GMC Sonoma, GMC Sierra and the Ford F-150, F-250 and F-350.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers

BACK-SAVER
BRUNO MODEL AWL-1600
Now you can enjoy owing a pickup truck along with the advantage of storing your folding wheelchair inside, out of the weather.
The Back-Saver is simple to operate and does not require any manual lifting. Just fold the chair up and roll the chair onto the platform. Turn the key to the ON position and depress the rocker switch to the UP position. Unloading the chair is just as simple and trouble-free.
The Back-Saver is rated to handle most folding wheelchairs with 22-inch or larger rear wheels, weighing 70 lbs. or less.
Bruno's Back-Saver will fit a standard Class I hitch tongue or a Class II or Class III if an adapter is used. And the Back-Saver features a strong tubular frame, for structural rigidity and long term durability.
A self-locking hold-tite bar is an integral part of the Back-Saver and is designed to grip the chair firmly during transport, without marring its finish.
In addition, the Back-Saver meets state and federal D.O.T. regulations for license plate illumination and visibility. The Back-Saver also includes an extra brake light for security and peace of mind.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers

OUT-RIDER
Now you can load your wheelchair or fully-assembled scooter into the bed of your pickup from inside the cab
The Out-Rider can be installed behind the cab on either the driver's or passenger's side of the truck. It is fully automatic and draws its power from the vehicle's battery. No welding is required and the unit is completely weatherized.
Expert installation and complete after-sale service is provided by Bruno's nationwide and international network of dealers.
The Out-Rider will add a new dimension to your lifestyle. The hand-held controller is simple and easy to operate. Just press a button and the Out-Rider does the rest.
Bruno also offers the EZ RIZER seat lift system to assist wheelchair or scooter users who may find it difficult to transfer into and out of full size trucks or 4x4's. Plus, Bruno's POW'R TOPPER covers your scooter or wheelchair in the truck's bed.
Call Bruno's Technical Applications Department for additional information about other great products.
Mobility Reimbusement may be available if you buy a new car
All interior vehicle lifts now come equipped with the R3 Lift Strap - An Industry First!
3 Years on Parts for Scooter Lifts and Wheelchair Lifts - 30 Days Labor!
(Interior Lifts)
Bruno manufactures over 24 different scooter lifts, power chair lifts, and wheelchair lifts for cars, minivans, vans, trucks, and sport utility vehicles. Bruno lifts can raise most scooters, wheelchairs and power chairs up to 400 lbs. All Bruno wheelchair lifts and scooter lifts are eligible for reimbursement of up to $1000.00 from General Motors, Saturn, Ford, Daimler Chrysler, Toyota, Lexus and Volkswagen under the terms of their Mobility Programs.
Scooter Lifts
Trunk Applications
Van, Truck or Sport Utility Applications
Outside Hitch Applications
Power Chair Lifts
Van, Truck or Sport Utility Applications
Outside Hitch Applications
Wheelchair Lifts
Trunk Applications
Van, Truck or Sport Utility Applications
Outside Hitch Applications
authorized dealer Bruno
WORLD'S LOWEST PRICES
1(800)446-5040
Over 1001 Electric Home Care Products - New & Used |
|
Adjustable Beds come in your choice
of Twin, Full, Queen, King, Dual Queen and Dual King Sizes;
|
Patient Lifts are available for
Bath, Pool and Spa; Hoyer and Ceiling Types. Patient lifts are designed
for caregivers to
lift |
Bariatric Heavy-Duty from
400 pound up to 1000 pound weight capability Adjustable Beds, Hospital Beds,
Lift-Chairs, Mattresses,
|
Scooters allow you to
electrically go forward and reverse at the simple touch of your finger.
Choose from indoor,
|
Hospital
Beds
are available in semi-electric 2 motor and fully electric 3 motor models.
Standard size is 36” wide by 80”
long. All sizes, mattresses, heavy-duty and
low-to-floor models are available. Options include side rails, trapeze
bar and table. Choose from Invacare, Tuffcare, Sunrise Medical, Merits, Gendron,
Transfer Master, Sleeper Lounge and Volkner. |
Scooter-Lifts and
Ramps simplify the transportation
of your scooter. Scooter-Lift models are available for almost all
|
Lift-Chairs
allow you to electrically stand, sit and
recline at the simple touch of your finger. All sizes, styles, heights,
widths,
|
Stair-Lifts allow you to travel
up and down your stairway at the simple touch of your finger. Available
in both
|
Massage Chairs by Panasonic offer outstanding deep tissue relief,
which can temporarily relax tense muscles, offering
|
Wheelchairs allow you to go forward
and reverse and turn with the simple touch of your finger. Models include
front,
mid |
Mattresses come in your choice
of Air, Innerspring, Latex-Foam and Tempur-Pedic. For Medical Purposes,
|
Wheelchair Elevators and Lifts
are available for residential and
commercial; indoor and outdoor usage. Standard
|
WORLD'S LOWEST PRICES: (800)477-0248 |
|
MEMBER BBB-ID#49501 - SINCE 1964
Please call for an illustrated brochure and price list
We have never lost sight of the fact that our success is built upon
offering the Public the best Price, Quality Guarantee and Service . .
."We Only Do One Thing And It Is For
You!"
[Adjustable
Beds]
[Bariatric
Eq.]
[Hospital
Beds]
[Lift-Chairs]
[Massage
Chairs]
[Mattresses]
[Patient-Lifts]
[Ramps][Scooters]
[Scooter-Lifts]
[Sleep-Room][Stair-Lifts]
[Used][Wheelchairs]
[Wheelchair-Elevators]

Adjustable Beds come in your
choice of Twin, Full, Queen, King, Dual Queen and Dual King Sizes; Innerspring,
Air, Latex Foam and Tempur-Pedic Mattresses. Options include Remote,
Massage, Wall-Hugger, 3-Motor, Side Rails, Heavy Duty and All Custom.
Choose from Electropedic, S-Cape, Adjusta-Magic, Flex-A-Bed, Med-Lift, Orthomatic
and L & P.
Bariatric
Heavy-Duty