The product described herein, manufactured by Mac's Lift Gate Inc., Long Beach, CA, is a precision vertical platform lifting device consisting of a machine tower with lifting platform, selected and dimensioned to provide adequate lifting height to suit the residential building requirement. The lift is capable of being used indoors and outdoors to vertically transport a wheelchair user or otherwise mobility-impaired person, up and over a low-rise barrier created by stairs, thus creating access to or within the building.
MAC'S Vertical home Lift PL-50 PL50 PL72 Elevator, mobility, matress
MAC'S Vertical home Lift PL-50 PL50 PL72 Elevator
A company with not less than forty (40) years of experience in the design, fabrication and installation of specialized lifting equipment for handicapped and geriatric consumers should supply the lift.
The unit shall be assembled and pre-wired (less optional equipment and necessary
gates) and manufactured with adequate lifting and load capacity for application
described elsewhere in this specification.
The unit shall be easy to operate by the user or attendant, and shall be
capable of functioning in all weather conditions.
The unit shall have the capacity to lift up to 500lbs. to the desired
lifting height up to a maximum lift height of 50 inches (4 feet 2 inches)
and 72 inches (6 feet).
Machine tower: 14 gage cold rolled steel.
Base frame: 1 1/2" square x 3/16" wall structure steel tubing.
Lift weldment: 1 1/2" x 3" x .188" wall structure steel tubing.
Tower cap: 10 gage cold rolled steel plate
Side Guard Panels: 20 gage cold rolled steel sheet panel, 1" square
x .120" & .083" gauge steel tubing (frame).
Platform: 14 gage cold rolled steel plate with slip resistance surface.
Access ramp: 11 gage steel steel plate with slip resistance surface.
Electrical box: 16 gage galvanized steel
Switch box: Hi-impact A.B.S. Thermoplastic instrument case.
Limitations: Vertical platform lift shall operate both indoors and
out, and must be anchored on a level, 4" thick, 3500 psi reinforced concrete
surface or pad.
The unit shall be pre-wired by manufacturer with exterior grade thermoplastic coated wiring. Extension Cord, 14 gage Ul-cSA approved is recommended if power source is not within three (3) feet of Machine tower. Machine may also be wired using water proof conduit.
![[Image]](pict895.jpg)
![[Image]](pict896.jpg)
1. 3 Stage wash, soapy water, clear water, and Iron Phosphate which
is applied to parts.
2. Parts are inspected and scuffed
3. Epoxy Primer is applied
4. Parts are baked at 250 degrees for 15 minutes
5. Parts are inspected and scuffed if needed
6. Huebert O'Brian Powder-TGIC Polyester
7. Mixed with Paint, Color Almond PFT-500-S8
8. Powder Coat is applied and baked at 400 degrees for 30 minutes
9. Parts are inspected and scuffed if needed
The unit shall have the following safety features for protection of users and the general public:
 |
Upper and lower limit switches
| Final limits switch
| Instant Reverse Motor
| Powered with 110 volt AC current, by 1/2 HP motor, 6.4 Amp
| Grounded electrical system
| Heavy duty worm drive gear box with heavy duty #50 lifting chain
| Automatic access ramp
| 36" solid sides on non-enter and exit sides of platform
| Non-Skid platform and access ramp surface
| Key-lock control
| Emergency stop switch on main platform control
| Platform safety pan to stop decent of platform if obstruction is encountered
| 3" locking top and bottom landing gates provided with mechanical G.A.L. interlock
| Switching & Control system 24 VAC low voltage current |
The contractor shall do all work and supply all materials necessary for the complete installation. It is the intent of this specification to outline boradly the equipment required but not to cover the details of design and construction.
Maintenance of the vertical platform lift unit shall consist of regular cleaning of the unit, protection of the painted surface of the unit.
Unit shall have one (1) year limited warranty on the basic unit and electrical system with a two (2) year warranty of drive train components.
This specification has been written to assist you and your consumer in preparing an accurate and detailed descsription for specifying a vertical platform lift. All or part of this specification may be reproduced. Additional technical information is available from our Product Engineering Department.
MAC’S Vertical Home Lift System Type |
||
PL-50 ( Maximum platform lifting height 50”) |
|
|
PL-72 ( Maximum platform lifting height 72”) |
|
|
MAC’S Vertical Home Lift System Options-Add to System Price |
||
Right turn 90 Degree
Exit Platform |
|
|
Safety Pan
Platform |
|
|
Solid
Sides
Platform
(36”high; does NOT include Platform Gate option) |
|
|
Larger
Platform
(35”wide x 54” long) |
|
|
Bolt on
Platform
(To
help get lift indoors, around corners or upstairs; specify when
ordering) |
|
|
Upper Landing
Gate
(36” high & includes
Interlock)
|
|
|
Larger Upper Landing
Gate (36” high 35” W & includes
Interlock |
|
|
90 Deg Upper Landing
Gate (36” high & includes
Interlock) |
|
|
Platform Gate &
Solid Sides (36” high &
includes Interlock; avail w/Solid Sides ONLY) |
|
|
Strike for Door
or Gate |
|
|
Emergency
Stop |
|
|
Call/Send Switches
(2) |
|
|
Hand Held
Remote |
|
|
Extra
Transmitter |
|
|
Bolt on Hand
Rail |
|
|
Portable System |
|
|
DC System
–
Battery Powered Lift |
|
|
ANSI System – See Pricing & Options
Below |
|
|
MAC’S Vertical
Home Lift ANSI
System
-$1,500.00 deposit w/order
required |
|
|
PL-50 ANSI
Lift (Includes safety features below *
; max platform lifting height 50”) |
|
|
PL-72 ANSI
Lift (Include safety features below *
; max platform lifting height 72”) |
|
|
*Call/Send Switches
(2)
*Emergency
Stop
*Solid Sides
(36”
high)
*Safety Pan
*Upper Landing
Gate (36” high &
includes Interlock)
*Platform
Gate
(36” high & includes Interlock) |
||
MAC’S Vertical Home Lift ANSI System Options-Add to ANSI System Price |
Price |
|
90 Degree Exit
Platform (Includes 90
Deg Upper Landing Gate, Platform Gate & Interlocks) |
|
|
DC System –
Battery Powered Lift
(Does NOT include battery, requires one U1
battery) |
|
|
MAC’S PSL-50 Portable
Stage Lift deposit w/order required
|
Price |
|
PSL-50 Portable Stage
Lift (Includes safety features
below * ; max platform lifting height 50” |
|
|
*Call/Send Switches
(2)
*Emergency
Stop
*Solid
Sides
(36”
high)
*Safety Pan
*Entrance & Exit
Side Platform
Gates
(36’high & includes
Interlock)
*Portable |
||
SERVING ALL OF LA wheelchair elevator, wheel chair vertical lift platform LOS ANGELES |
| LA MAC'S Vertical Home Lift PL50 & PL72 Specifications Wheelchair Elevator Los Angeles for School, Porch, Mobile Home, Residential, Commercial, Church - American Disabilities Act - ADA - Handicap Elevators |
LA ELEVATOR, LOS ANGELES
Porch School Mobile Home Church Wheelchair Elevators
Before You Buy An Electric Wheelchair-Elevator, we ask you the
following
questions:
1. How many feet do you have to go up?
If you are using the Wheelchair Elevator for a simple Porch-type
Setting, we would highly recommend the
MAC PL-50 (for up to 52")
or the PL-72 (up to 72") or the Wheelchair Elevators by
Trus-T-Lift. The
Trus-T-Lift manufactures Models that can go all the way up from the first
story to the second story.
ConcordMac's LiftTrus-T-LiftRam Manufacturing
|
